Hall effects and entropy generation applications for peristaltic flow of modified hybrid nanofluid with electroosmosis phenomenon

The electroosmotic peristaltic flow of modified hybrid nanofluid in presence of entropy generation has been presented in this thermal model. The Hall impact and thermal radiation with help of nonlinear relations has also been used to modify the analysis. The assumed flow is considered due to a non-uniform trapped channel. The properties of modified hybrid nanofluid model are focused with interaction of three distinct types of nanoparticles namely copper ($Cu)$, silver ($Ag$) and aluminum oxide ($A{l}_2{O}_3).$ The mathematical modeling and significances of entropy generation and Bejan number are identified. With certain flow assumptions, the governing equations are attained for optimized peristaltic electroosmotic problem. Widely used assumptions of long wave length and low Reynolds number reduced the governing equations in ordinary differential equations. The ND solver is flowed for the solution process. The physical significant of results is observed by assigning the numerical values to parameters.     

Retention of alkali,alkaline earth and transition metals on an itaconic acid cation-exchange column. Eluent pH,ionic strength and temperature effects upon selectivity

The unusual selectivity of a methylene succinic (itaconic) acid modified polymeric column was investigated for the separation of alkali, alkaline earth, transition and heavy metals employing non-chelating inorganic eluents. The retention of selected metal ions on the column was investigated with simple HNO3 eluents and eluents prepared from KNO3 and KCl salts of varying pH (adjusted using HNO3). From these studies both the effect of eluent ionic strength and pH upon retention was evaluated for the itaconic acid stationary phase. The results obtained showed that despite slow exchange kinetics causing poor efficiencies, acceptable baseline separations of selected alkaline earth and transitions could be obtained under optimum conditions (the baseline separation of Mg(II), Ca(II), Mn(II), Cd(II), Zn(II) and Co(II) was possible using a 15 mM KNO3-5 mM KCl eluent at pH 3.50 in under 25 min). The use of an simple ionic strength step gradient was shown that facilitated the addition of Pb(II) to the above group of metal ions. An investigation into the effect of temperature upon peak efficiency and retention showed increased column temperature could be used to improve the resolution of closely eluting metal ions such as Ca(II) and Sr(II) and Ca(II) and Mn(II).     

Melt drawing as a route to high performance polyethylene

Well established routes for obtaining stiff and strong polyethylene (PE) involve solid state drawing either of solution crystallized gel films or melt crystallized spherulitic PE. The aim of this work is to show the potential of melt deformation as an alternative route for obtaining highly oriented products. Our previous work on the melt deformation route showed that oriented PE fibers could be directly extruded under appropriately controlled conditions [8,9]. Here, we show that PE films (or filaments) can also be melt drawn in the temperature window 130–160 °C, thus yielding oriented products. The advantage of melt drawing over direct melt extrusion is that it allows a wider operational latitude and thus does not require such carefully controlled conditions.The morphology produced by melt deformation is different from solid state deformation and consists of extended chain fibrils with platelet overgrowths. The relative amount of fibrils and platelets depends on operating parameters. The temperature window of PE melt drawing is identified with the regime where some flow induced crystallization takes place. The conditions for melt drawability are of wider generality for crystallizable flexible chain polymers. They are: (i) adequate strain rate to overcome entropie resistance to chain extension, (ii) but not high enough to activate the elastic response of the transient networks in the entangled system, (iii) sufficient strain to fully extend the chain, (iv) appropriate temperature for flow-induced crystallization and strain hardening, and (v) cooling to freeze the oriented structure.Ultra high molecular weight PEs were not the most suitable for melt drawing due to their high recoverable elongation in the melt (melt elasticity) in addition to added limitations imposed by their nascent grain systeme. Our work suggests that an optimum molecular weight for melt drawing is¯M _w(400–900)×10³ with further possibilities for improvement through multimodal distributions.     

Flow-injection spectrophotometric determination of chloramben

Abstract

A method for the dechlorination of PCB mixtures (Aroclor formulations) to biphenyl was extended to soils. The contaminated sample was mixed with magnesium flakes, potassium hexachloropalladiate (K₂PdCl₆), propan-2-ol and water then permitted to react for up to six hours. Biphenyl, recovered by extraction into hexane, was quantified by gas chromatography with flame ionization detection. The reaction was very efficient in propan-2-ol / water (～95%), surfactant emulsion or sand mixture and virtually complete in soil provided that excess magnesium (2 g) and the K₂PdCl₆ were added to the sample prior to the addition of water. Higher PCB loadings were readily determined in field contaminated soils either by direct determination within the matrix or by standard additions. However, analyte concentrations were appreciably over-estimated in Soxhlet or sonication extracts of a certified reference material that contained sub-ppm levels of analyte. The over-estimation is considered to result from the conversion in part of natural organic matter to biphenyl.     

Characterization of ion irradiated silicon surfaces ablated by laser-induced breakdown spectroscopy

Low energy metallic ions,generated by a Q-switched Nd:YAG laser(1064-nm wavelength,10-mJ energy,9-nm～12-ns-pulse width,10~(11)W/cm~2intensity)irradiated on a silicon substrate to modify various properties,such as electrical,morphological,and structural modifications.Thomson parabola technique is used to calculate the energy of these metallic ions whereas the electrical conductivity is calculated with the help of Four-point probe.Interestingly circular tracks forming chain like damage trails are produced via these energetic ions which are carefully examined by optical microscopy.It is observed that excitation,ionization,and cascade collisions are responsible for surface modifications of irradiated samples.Four-point probe analysis revealed that the electrical conductivity of substrate has reduced with increasing trend of atomic number of irradiated metallic ions(Al,Ti,Cu,and Au).The x-ray diffraction analysis elucidated the crystallographic changes leading to reduction of grain size of N-type silicon substrate,which is also associated with the metallic ions used.The decreasing trend of conductivity and grain size is due to thermal stresses,scattering effect,structural imperfections,and non-uniform conduction of energy absorbed by substrate atoms after the ion irradiation.     

Spectroscopic and morphological study of laser ablated Titanium

The optical characteristics of biological tissues sampled from the anterior abdominal wall of laboratory rats are for the first time experimentally studied in a wide wavelength range (350-2500 nm). The experiments have been performed in vitro using a LAMBDA 950 (PerkinElmer, United States) spectrophotometer. Inverse Monte Carlo simulation is used to restore the spectral dependences for scattering and absorption coefficients, as well as the scattering anisotropy factor for biological tissue based on the recorded spectra of diffuse reflection and total and collimated transmissions.     

Study of Pion Transverse Momentum Distributions in Ultra-Relativistic Heavy Ion Collisions: A USTFM Approach

Journal of Experimental and Theoretical Physics - The mid-rapidity (|y| < 0.5) transverse momentum distributions of identified charged pions produced in different collision systems at...